Plan your railway
Most first layouts that stall do so because of decisions made in the first week: a scale that doesn't fit the room, a track plan with too much track, or a baseboard you can't reach across. Time spent here saves money later.
Choose a scale
Scale is the size of the models. Gauge is the distance between the rails. These are the common choices. Pick the one whose trains you like, and check that it fits your space.
| Scale | Ratio | Track gauge | Simple oval needs roughly | Good for |
|---|---|---|---|---|
| N | 1:148 (UK) / 1:160 | 9 mm | 1.2 × 0.6 m | Long trains and big scenes in small spaces. Fiddlier to handle. |
| TT:120 | 1:120 | 12 mm | 1.5 × 0.9 m | A newer middle ground with a fast-growing UK range. |
| OO | 1:76 | 16.5 mm | 1.8 × 1.2 m | The UK's most popular scale, with the widest range of British models. |
| HO | 1:87 | 16.5 mm | 1.8 × 1.2 m | The world standard for North American and European models. |
| O | 1:43.5 (UK) / 1:48 | 32 mm | 3 × 2 m+ | Big, weighty, detailed models. Suits shunting layouts and garden lines. |
Step by step
- Measure your space, including doors, windows and heaters. Keep any board you need to reach across under about 60 cm deep.
- Pick a scale using the table above. Don't buy trains until you've decided.
- Choose a theme: a country, a rough era and a kind of railway (branch line, main line or industrial). This keeps your purchases consistent.
- Pick a layout type. A continuous run (oval) lets trains circle. An end-to-end or shunting plank is about operation, and suits shelves. A round-the-room layout gives the longest run.
- Draw a track plan at scale, on paper or in free software such as SCARM or AnyRail. Use the real geometry of the track you'll buy.
- Decide DC or DCC (see Stop 4) before buying locomotives, so that you buy the right fittings.
- Set a budget and buy in stages. Track and baseboards come first, then scenery.
Avoid these mistakes
- Cramming in as much track as possible. Leave space for scenery.
- Curves tighter than your locos can manage. Use the largest radius that fits.
- Gradients steeper than about 1 in 40 (2.5%).
- Boards too deep to reach the back of.
Tip
Start small. A finished 1.2 m shunting layout teaches you every skill in this guide. Half-built empires rarely do.
Build the baseboards
The baseboard is the foundation of everything else. It must be flat, rigid and stable. If it warps, sags or flexes, track will misalign and trains will derail, no matter how carefully you lay it.
Step by step
- Choose your method. Laser-cut plywood kits are the quickest way to a square, accurate result. A DIY open frame is cheaper and fully customisable.
- Build a frame from straight softwood or plywood strips, with cross-members every 30–40 cm. A common board size is 1200 × 600 mm.
- Add a top of 6–9 mm plywood. Lightweight extruded foam (XPS) is also an option. Keep any area for future hills open, so that you can build landforms later.
- Check it's square by measuring both diagonals. They should match.
- Set the height. About 1 m is comfortable to work at and to watch from. Higher looks more realistic, but young children may not see.
- Level it in both directions with a spirit level. Use adjustable feet if possible.
- Join multiple boards with alignment dowels and bolts, so that they line up the same way every time.
You'll need
- Plywood or a baseboard kit
- Saw, drill/driver, wood screws
- Wood glue, clamps, set square
- Spirit level, tape measure
Avoid these mistakes
- Chipboard or MDF tops. They are heavy, sag and swell when ballast glue soaks in.
- No space underneath for wiring or point motors.
- Building in an unheated loft or shed without allowing for damp and temperature swings.
Lay the track
Smooth, reliable running comes from accurate track laying. This is the stage to take slowly. Every kink or misaligned joint will cause derailments later, and fixing it once scenery is in place is painful.
Step by step
- Mark the plan full size on the baseboard, and check that clearances and curves work in practice.
- Lay underlay (cork or foam) along the track route. It deadens noise and gives a shoulder for ballast.
- Position the points (turnouts) first, then join plain track to them. Points are the least flexible pieces.
- Cut flexible track cleanly with rail cutters, then file off any burrs so that rail joiners slide on.
- Join every rail with rail joiners (fishplates). Use insulated joiners wherever the plan needs electrical breaks.
- Fix the track lightly with track pins or a flexible adhesive, so that it can still be adjusted.
- Test thoroughly. Push your longest coach and fastest loco through every route, in both directions, before anything is permanent.
Know your points
- Insulfrog: plastic crossing (frog). Simplest to wire, but short locos can stall on it.
- Electrofrog: metal frog. Best running, but needs extra gaps and wiring.
- Unifrog: a newer PECO design that works out of the box and can be upgraded to a live frog later.
Avoid these mistakes
- Joints on curves. Bend flexi-track so that its joints fall on straights where possible.
- Reverse (S) curves with no straight between them.
- Pins hammered in so far that they distort the sleepers.
Wire it up
Wiring frightens more beginners than anything else, but a simple layout needs only a few principles: give the rails reliable feeds, keep the wires tidy and labelled, and test as you go.
| DC (analogue) | DCC (digital) | |
|---|---|---|
| How it works | The controller varies the track voltage. Every loco on that section moves together. | The track carries constant power plus digital commands. Each loco has a decoder with its own address. |
| Running several trains | Needs isolating sections and switches. | Built in. Drive each loco independently anywhere. |
| Cost to start | Lower | Higher: a command station plus decoders. |
| Best for | Small layouts, one train at a time, tight budgets. | Multiple trains, sound, and avoiding complex section wiring. |
Step by step
- Run a power bus: a pair of heavier wires under the baseboard (around 1.0–1.5 mm²/16–14 AWG). Use one colour for each rail, and keep to it everywhere.
- Add droppers: short, thinner wires soldered to the rails (or use pre-wired joiners) and taken down through the board to the bus. Aim for a feed to every length of rail.
- Learn to solder: clean the joint, use flux, heat the work rather than the solder, and keep it quick so that sleepers don't melt.
- Choose point control: by hand, solenoid motors (fire with a capacitor discharge unit), slow-action stall motors, or servos.
- For electrofrog points, switch the frog polarity using the motor's built-in switch or a frog juicer.
- Test each section as you connect it, not the whole layout at the end. With DCC, a coin laid across the rails anywhere should trip the short-circuit protection.
- Label everything under the board. You will thank yourself later.
You'll need
- Bus wire and dropper wire (two colours)
- Temperature-controlled soldering iron, solder, flux
- Wire strippers, cutters, connectors
- Multimeter (inexpensive, invaluable)
Avoid these mistakes
- Relying on rail joiners to carry power. They loosen and corrode.
- Swapping wire colours midway.
- Hiding joints where you can never reach them again.
Ballast & weather the track
Ballast turns toy-like track into a convincing railway. The method is simple and rewards patience. Do it only once every route runs reliably, because glued ballast makes track very hard to adjust.
Step by step
- Weather the rails first (optional). Paint rail sides rust-brown and sleepers a weathered grey-brown, then wipe the railheads clean.
- Mask the points: keep ballast away from the tie-bar and moving blades. Tape or a dab of oil helps.
- Spread dry ballast with a spoon or small cup, then brush it into shape with a soft brush. Tap the sleepers so that ballast settles below their tops.
- Mist with water mixed with a drop of washing-up liquid (or with isopropyl alcohol) so that glue wicks in evenly.
- Apply diluted PVA (around 1 part glue to 3 parts water, plus a drop of detergent) with a pipette or syringe. Let it soak in. Don't flood it.
- Leave it 24 hours, then vacuum loose grains, work the points, and clean the railheads.
Avoid these mistakes
- Glue in the moving parts of points. It is the most common way to ruin one.
- Ballast heaped over the sleeper tops.
- Ballasting before full running tests.
Tip
Practise on an offcut of track first. Ballast colour also matters: real ballast is rarely uniform grey, so a mix of two shades looks more natural.
Create the landscape
Scenery is built in layers, much like nature: shape the land, colour the earth, then add grass, bushes, trees and water. Variety is the secret. Real landscapes are never one shade of green.
The layers, in order
- Landforms: carve foam, or build a card lattice covered with plaster cloth, then smooth it with a material such as Sculptamold.
- Earth colour: paint all terrain a mid earth-brown, so that any gaps in the cover read as soil.
- Base scatter: sprinkle fine scatter and real dirt into wet glue for paths and bare patches.
- Static grass: an applicator makes fibres stand upright. Lay short grass first, then longer tufts and weeds in layers.
- Bushes and undergrowth along fences, at the bases of trees, and where ground meets buildings.
- Trees: twisted wire, ready-made armatures, or natural materials such as seafoam, with foliage added. Vary their sizes.
- Water: paint the bed darker towards the deepest point, seal it, then pour resin or apply water gel in thin layers.
You'll need
- Foam or card, plaster cloth, filler
- Earth-coloured acrylic paint, PVA, spray glue
- Static grass applicator and fibres (2–6 mm)
- Scatter, foliage, tree armatures or wire
- Water resin or gel
Avoid these mistakes
- One colour and one length of grass everywhere.
- Trees all the same height, planted in neat rows.
- Pouring resin on an unsealed base. It leaks and bubbles.
Add buildings & structures
Buildings give your railway a sense of place and purpose. Start with a kit, then try scratch-building once you're confident. The difference between toy-like and realistic is mostly in the finishing.
Step by step
- Pick your approach: printed card kits are cheap and quick, plastic kits are crisp and detailed, ready-made resin needs only placing, and scratch-building gives you anything you want.
- Paint and weather: knock the shine off plastic with matt varnish, add grime with washes, and pick out window frames and doors.
- Block light leaks if you'll light the building. Paint the inside of the walls black, then white.
- Bed it into the ground. Blend the base with scatter, weeds and paths so that there is no visible gap.
- Add life: gutters, signs, clutter, fences and a figure or two.
Avoid these mistakes
- Shiny plastic straight from the box.
- White card edges showing at corners. Colour them in.
- Buildings that "float" on top of the scenery.
Look after your trains
A layout is only as good as how it runs. Clean track, clean wheels and the occasional drop of oil solve most running problems. Fitting decoders and weathering stock are satisfying next steps.
Step by step
- Run in new locos gently for 20–30 minutes in each direction.
- Clean the track regularly with a track rubber or isopropyl alcohol on a cloth. Avoid abrasive pads that scratch the rail.
- Clean wheels, especially loco pick-ups, which collect dirt and cause stalling.
- Lubricate sparingly: a tiny drop of plastic-safe oil on bearings and gears. Over-oiling attracts dirt.
- Fit DCC decoders if you've chosen DCC. Most modern locos have a plug-in socket (8-, 21-pin or Next18).
- Weather your stock with powders, washes or dry-brushing. No airbrush is needed to start.
Avoid these mistakes
- Oil on the track or wheels. It kills traction and electrical contact.
- Mixing coupling types across your fleet.
- Cleaning with solvents that attack plastic bodies.
Glossary
The jargon you'll hear in the videos, explained.
- Ballast
- The stone chippings that support real track. Modelled with fine granules glued around the sleepers.
- Bus
- A pair of main power wires under the baseboard that the track feeds connect to.
- CDU (capacitor discharge unit)
- Stores a burst of power to throw solenoid point motors firmly and safely.
- Code 75 / Code 100
- Rail height in thousandths of an inch. Code 75 looks finer. Code 100 is more robust and tolerates older wheels.
- DC
- Analogue control: the controller varies the track voltage to set speed and direction.
- DCC
- Digital Command Control. The track carries constant power and data, and each loco's decoder obeys its own commands.
- Decoder
- A small circuit board inside a DCC loco that receives commands and drives the motor, lights and sound.
- Dropper
- A short wire soldered to a rail and run down through the baseboard to the bus.
- Fishplate / rail joiner
- A metal sleeve joining two rails. Insulated versions create electrical breaks.
- Flexi-track
- Long lengths of track you bend to any curve and cut to length. It contrasts with fixed-geometry set-track.
- Frog
- The V-shaped crossing in a point where two rails cross. It can be plastic (insulfrog) or metal (electrofrog).
- Point / turnout / switch
- Track that diverts trains from one route to another. "Point" is UK usage. "Turnout" or "switch" is US usage.
- Radius
- How tight a curve is. Larger radii look better and run more reliably.
- Ready-to-run (RTR)
- Locos and wagons supplied finished and ready to use, as opposed to kits.
- Scatter
- Coloured granules or flock used for ground cover.
- Static grass
- Fibres charged by an applicator so that they stand upright like real grass.
- Tie-bar
- The moving bar that throws a point's blades from one route to the other.
- Weathering
- Adding dirt, rust and wear to models so that they look used rather than factory-fresh.
How we pick videos
For each topic we aim to recommend a small number of genuinely useful videos: one primary pick, one alternative, one deep dive and, where helpful, one quick answer.
Each fully reviewed video is scored from 1 to 5 on six criteria. A higher score is always better. For commercial bias, 5 means independent or transparently balanced.
| Criterion | 1 – Weak | 3 – Acceptable | 5 – Excellent |
|---|---|---|---|
| Beginner friendliness | Assumes substantial prior knowledge | Some terminology explained | Clear for a complete newcomer |
| Explanation quality | Shows actions without explaining why | Adequate explanation | Explains reasoning, choices and alternatives |
| Practical usefulness | Hard to reproduce | Useful with extra research | Viewer can confidently complete the task |
| Production quality | Difficult to see or hear | Generally clear | Excellent close-ups, sound and pacing |
| Currency | Outdated method or unavailable products | Mostly current | Current, relevant and easy to source |
| Commercial bias | Primarily promotional | Some promotion but useful | Independent or transparently balanced |
About "awaiting review" videos
Alongside our scored picks, each stage lists further candidate videos that we have found but not yet watched in full and scored. They're included so you can explore further. Popularity alone isn't a quality rating, so check that the method suits your scale and setup before following one.